Select your business area

We use this information to provide content associated with segment of your choice.
You can change your selection any time.

Træning

Få fuldt udbytte af din motor- og generatorstyring fra DEIF

Choose country

AGC

Service level Read more
26-11-2019 - 27-11-2019
Skive, Denmark
EUR 850
Few seats left
Register Read more

AGC

  • This training course is for service technicians and engineers who commission and troubleshoot genset operations.

Your outcome

  • You will learn how to use the different configuration inputs, modes of operation, and how to change protection settings.
  • You will learn how to use the controller and obtain in-depth knowledge of the functionalities it offers.
  • You will learn how to access the menus from the front panel display screen to activate, commission and troubleshoot typical applications. Input from you on your typical applications further build these skills.
  • You will learn how to connect the utility software and configure I/Os, parameter settings, and additional operator panels (AOP). This will also involve tuning of PIDs, synchronisation and using the utility software as a troubleshooting tool.

Course prerequisites

Attending the AGC advanced training session presupposes completion of the AGC Service course. 

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

PPM 300

Service level Read more
03-12-2019 - 04-12-2019
Skive, Denmark
EUR 850
Available
Register Read more

PPM 300

The two-day training course is for operators and service technicians. You will learn the basic functions of the PPM 300 controller and how to carry out daily routine operations. When familiar with the primary functions you will proceed with more advanced tasks such as setting up, troubleshooting and commissioning typical genset applications.

Your outcome

  • You will learn the basic menu functions of the genset controller and become acquainted with the menu structure
  • You will learn how to use the controller and obtain in-depth knowledge of the functionality it offers.
  • You will learn how to use the different configuration inputs, modes of operation and how to change protection settings.
  • You will learn how to connect the utility software, configure I/O’s, parameter settings etc.

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

MPO

Service level Read more
03-12-2019 - 04-12-2019
Skive, Denmark
EUR 850
Available
Register Read more

PPM 300

The two-day training course is for operators and service technicians. You will learn the basic functions of the PPM 300 controller and how to carry out daily routine operations. When familiar with the primary functions you will proceed with more advanced tasks such as setting up, troubleshooting and commissioning typical genset applications.

Your outcome

  • You will learn the basic menu functions of the genset controller and become acquainted with the menu structure
  • You will learn how to use the controller and obtain in-depth knowledge of the functionality it offers.
  • You will learn how to use the different configuration inputs, modes of operation and how to change protection settings.
  • You will learn how to connect the utility software, configure I/O’s, parameter settings etc.

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

PPU 300

Operator/Service Read more
28-01-2020 - 29-01-2020
Skive, Denmark
EUR 850
Available
Register Read more

PPU 300

The two-day training course is for operators and service technicians. You will learn the basic functions of the PPU 300 controller and how to carry out daily routine operations. When familiar with the primary functions you will proceed with more advanced tasks such as setting up, troubleshooting and commissioning typical genset applications. 

Your outcome

  • You will learn the basic menu functions of the genset controller and become acquainted with the menu structure
  • You will learn how to use the controller and obtain in-depth knowledge of the functionality it offers.
  • You will learn how to use the different configuration inputs, modes of operation and how to change protection settings.
  • You will learn how to connect the utility software, configure I/O’s, parameter settings etc.

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

PPM 300

Operator/Service Read more
30-01-2020 - 31-01-2020
Skive, Denmark
EUR 850
Available
Register Read more

PPM 300

The two-day training course is for operators and service technicians. You will learn the basic functions of the PPM 300 controller and how to carry out daily routine operations. When familiar with the primary functions you will proceed with more advanced tasks such as setting up, troubleshooting and commissioning typical genset applications.

Your outcome

  • You will learn the basic menu functions of the genset controller and become acquainted with the menu structure
  • You will learn how to use the controller and obtain in-depth knowledge of the functionality it offers.
  • You will learn how to use the different configuration inputs, modes of operation and how to change protection settings.
  • You will learn how to connect the utility software, configure I/O’s, parameter settings etc.

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

AGC

Service level Read more
04-03-2020 - 05-03-2020
Skive, Denmark
EUR 850
Available
Register Read more

AGC

  • This training course is for service technicians and engineers who commission and troubleshoot genset operations.

Your outcome

  • You will learn how to use the different configuration inputs, modes of operation, and how to change protection settings.
  • You will learn how to use the controller and obtain in-depth knowledge of the functionalities it offers.
  • You will learn how to access the menus from the front panel display screen to activate, commission and troubleshoot typical applications. Input from you on your typical applications further build these skills.
  • You will learn how to connect the utility software and configure I/Os, parameter settings, and additional operator panels (AOP). This will also involve tuning of PIDs, synchronisation and using the utility software as a troubleshooting tool.

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

AGI

Designer level Read more
19-03-2020
Skive, Denmark
EUR 425
Available
Register Read more

AGI

  • This training course is for designers who require detailed knowledge of the DEIF controllers capabilities in order to make the right offer to meet application requirements.Designers will learn how to specify a genset controller with regards to option selection, how to design an application for DEIF controllers and how to setup advanced power management applications.

Your outcome

  • You will learn how to use the technical documentation as a tool for option selection to meet application requirements
  • Through practical exercises, you will learn to setup advanced power management applications using DEIF Utility Software
  • Via hands-on training you will gain knowledge about different modes of operation in power management applications
  • You will learn to emulate an entire application though practical application and function training

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

DVC

Read more
25-03-2020 - 26-03-2020
Skive, Denmark
EUR 850
Available
Register Read more

DVC 310

This training course is for you who are working with commissioning and troubleshooting of digital voltage controllers (DAVR)

Your outcome

  • You will learn to set up and troubleshoot DEIF’s digital voltage regulator DVC 310
  • You will get an introduction to the DVC 310 hardware and the EasyReg PC configuration software. 
  • You will learn the different modes of the DVC 310 and how to use them, and how to interface to the DVC 310.

Course prerequisites

Attending the DVC training session presupposes completion of the AGC Service course

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

AGC 150

Service level Read more
01-04-2020 - 02-04-2020
Skive, Denmark
EUR 850
Available
Register Read more

AGC 150

  • This training course is for service technicians and engineers who commission and troubleshoot genset operations.

Your outcome

  • You will learn to navigate the controller and utility software. 
  • You will learn how to use the different configuration inputs, modes of operation, and how to change protection settings.
  • You will learn how to use the controller and obtain in-depth knowledge of the functionalities it offers.
  • You will learn how to access the menus from the controller screen to activate, commission and troubleshoot typical applications. Input from you on your typical applications, further build these skills.
  • You will learn how to connect the utility software and configure I/Os, and parameter settings. It will also involve tuning of PIDs, synchronisation and using the utility software as a troubleshooting tool. 

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.
The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

PPU 300

Operator/Service Read more
21-04-2020 - 22-04-2020
Skive, Denmark
EUR 850
Available
Register Read more

PPU 300

The two-day training course is for operators and service technicians. You will learn the basic functions of the PPU 300 controller and how to carry out daily routine operations. When familiar with the primary functions you will proceed with more advanced tasks such as setting up, troubleshooting and commissioning typical genset applications. 

Your outcome

  • You will learn the basic menu functions of the genset controller and become acquainted with the menu structure
  • You will learn how to use the controller and obtain in-depth knowledge of the functionality it offers.
  • You will learn how to use the different configuration inputs, modes of operation and how to change protection settings.
  • You will learn how to connect the utility software, configure I/O’s, parameter settings etc.

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

PPM 300

Operator/Service Read more
23-04-2020 - 24-04-2020
Skive, Denmark
EUR 850
Available
Register Read more

PPM 300

The two-day training course is for operators and service technicians. You will learn the basic functions of the PPM 300 controller and how to carry out daily routine operations. When familiar with the primary functions you will proceed with more advanced tasks such as setting up, troubleshooting and commissioning typical genset applications.

Your outcome

  • You will learn the basic menu functions of the genset controller and become acquainted with the menu structure
  • You will learn how to use the controller and obtain in-depth knowledge of the functionality it offers.
  • You will learn how to use the different configuration inputs, modes of operation and how to change protection settings.
  • You will learn how to connect the utility software, configure I/O’s, parameter settings etc.

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

AGC

Designer level Read more
29-04-2020 - 30-04-2020
Skive, Denmark
EUR 850
Available
Register Read more

AGC

  • This training course is for service technicians and engineers who commission and troubleshoot genset operations.

Your outcome

  • You will learn how to use the different configuration inputs, modes of operation, and how to change protection settings.
  • You will learn how to use the controller and obtain in-depth knowledge of the functionalities it offers.
  • You will learn how to access the menus from the front panel display screen to activate, commission and troubleshoot typical applications. Input from you on your typical applications further build these skills.
  • You will learn how to connect the utility software and configure I/Os, parameter settings, and additional operator panels (AOP). This will also involve tuning of PIDs, synchronisation and using the utility software as a troubleshooting tool.

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

PPU 300

Operator/Service Read more
12-05-2020 - 13-05-2020
Skive, Denmark
EUR 850
Available
Register Read more

PPU 300

The two-day training course is for operators and service technicians. You will learn the basic functions of the PPU 300 controller and how to carry out daily routine operations. When familiar with the primary functions you will proceed with more advanced tasks such as setting up, troubleshooting and commissioning typical genset applications. 

Your outcome

  • You will learn the basic menu functions of the genset controller and become acquainted with the menu structure
  • You will learn how to use the controller and obtain in-depth knowledge of the functionality it offers.
  • You will learn how to use the different configuration inputs, modes of operation and how to change protection settings.
  • You will learn how to connect the utility software, configure I/O’s, parameter settings etc.

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

AGI

Designer level Read more
14-05-2020
Skive, Denmark
EUR 425
Available
Register Read more

AGI

  • This training course is for designers who require detailed knowledge of the DEIF controllers capabilities in order to make the right offer to meet application requirements.Designers will learn how to specify a genset controller with regards to option selection, how to design an application for DEIF controllers and how to setup advanced power management applications.

Your outcome

  • You will learn how to use the technical documentation as a tool for option selection to meet application requirements
  • Through practical exercises, you will learn to setup advanced power management applications using DEIF Utility Software
  • Via hands-on training you will gain knowledge about different modes of operation in power management applications
  • You will learn to emulate an entire application though practical application and function training

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

PPU 300

Codesys Read more
14-05-2020
Skive, Denmark
EUR 425
Available
Register Read more

PPU 300 Codesys

The PPU 300 CODESYS training is for switchboard builders and system integrators. The training course will provide you with tools and knowledge on how to use the PPU 300 in a CODESYS application. The training includes various hand-on sessions and will enable you to make customised project solutions.

Course prerequisites

Attending the PPU 300 Codesys training session tracompletion of the PPU 300 Service course. 

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

AGC

Service level Read more
10-06-2020 - 11-06-2020
Skive, Denmark
EUR 850
Available
Register Read more

AGC

  • This training course is for service technicians and engineers who commission and troubleshoot genset operations.

Your outcome

  • You will learn how to use the different configuration inputs, modes of operation, and how to change protection settings.
  • You will learn how to use the controller and obtain in-depth knowledge of the functionalities it offers.
  • You will learn how to access the menus from the front panel display screen to activate, commission and troubleshoot typical applications. Input from you on your typical applications further build these skills.
  • You will learn how to connect the utility software and configure I/Os, parameter settings, and additional operator panels (AOP). This will also involve tuning of PIDs, synchronisation and using the utility software as a troubleshooting tool.

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

PPU 300

Operator/Service Read more
08-09-2020 - 09-09-2020
Skive, Denmark
EUR 850
Available
Register Read more

PPU 300

The two-day training course is for operators and service technicians. You will learn the basic functions of the PPU 300 controller and how to carry out daily routine operations. When familiar with the primary functions you will proceed with more advanced tasks such as setting up, troubleshooting and commissioning typical genset applications. 

Your outcome

  • You will learn the basic menu functions of the genset controller and become acquainted with the menu structure
  • You will learn how to use the controller and obtain in-depth knowledge of the functionality it offers.
  • You will learn how to use the different configuration inputs, modes of operation and how to change protection settings.
  • You will learn how to connect the utility software, configure I/O’s, parameter settings etc.

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

PPM 300

Operator/Service Read more
10-09-2020 - 11-09-2020
Skive, Denmark
EUR 850
Available
Register Read more

PPM 300

The two-day training course is for operators and service technicians. You will learn the basic functions of the PPM 300 controller and how to carry out daily routine operations. When familiar with the primary functions you will proceed with more advanced tasks such as setting up, troubleshooting and commissioning typical genset applications.

Your outcome

  • You will learn the basic menu functions of the genset controller and become acquainted with the menu structure
  • You will learn how to use the controller and obtain in-depth knowledge of the functionality it offers.
  • You will learn how to use the different configuration inputs, modes of operation and how to change protection settings.
  • You will learn how to connect the utility software, configure I/O’s, parameter settings etc.

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

AGI

Designer level Read more
17-09-2020
Skive, Denmark
EUR 425
Available
Register Read more

AGI

  • This training course is for designers who require detailed knowledge of the DEIF controllers capabilities in order to make the right offer to meet application requirements.Designers will learn how to specify a genset controller with regards to option selection, how to design an application for DEIF controllers and how to setup advanced power management applications.

Your outcome

  • You will learn how to use the technical documentation as a tool for option selection to meet application requirements
  • Through practical exercises, you will learn to setup advanced power management applications using DEIF Utility Software
  • Via hands-on training you will gain knowledge about different modes of operation in power management applications
  • You will learn to emulate an entire application though practical application and function training

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

AGC

Service level Read more
23-09-2020 - 24-09-2020
Skive, Denmark
EUR 850
Available
Register Read more

AGC

  • This training course is for service technicians and engineers who commission and troubleshoot genset operations.

Your outcome

  • You will learn how to use the different configuration inputs, modes of operation, and how to change protection settings.
  • You will learn how to use the controller and obtain in-depth knowledge of the functionalities it offers.
  • You will learn how to access the menus from the front panel display screen to activate, commission and troubleshoot typical applications. Input from you on your typical applications further build these skills.
  • You will learn how to connect the utility software and configure I/Os, parameter settings, and additional operator panels (AOP). This will also involve tuning of PIDs, synchronisation and using the utility software as a troubleshooting tool.

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

AGC 150

Service level Read more
07-10-2020 - 08-10-2020
Skive, Denmark
EUR 850
Available
Register Read more

AGC 150

  • This training course is for service technicians and engineers who commission and troubleshoot genset operations.

Your outcome

  • You will learn to navigate the controller and utility software. 
  • You will learn how to use the different configuration inputs, modes of operation, and how to change protection settings.
  • You will learn how to use the controller and obtain in-depth knowledge of the functionalities it offers.
  • You will learn how to access the menus from the controller screen to activate, commission and troubleshoot typical applications. Input from you on your typical applications, further build these skills.
  • You will learn how to connect the utility software and configure I/Os, and parameter settings. It will also involve tuning of PIDs, synchronisation and using the utility software as a troubleshooting tool. 

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.
The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

DVC

Read more
21-10-2020 - 22-10-2020
Skive, Denmark
EUR 850
Available
Register Read more

DVC 310

This training course is for you who are working with commissioning and troubleshooting of digital voltage controllers (DAVR)

Your outcome

  • You will learn to set up and troubleshoot DEIF’s digital voltage regulator DVC 310
  • You will get an introduction to the DVC 310 hardware and the EasyReg PC configuration software. 
  • You will learn the different modes of the DVC 310 and how to use them, and how to interface to the DVC 310.

Course prerequisites

Attending the DVC training session presupposes completion of the AGC Service course

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

AGI

Designer level Read more
22-10-2020
Skive, Denmark
EUR 425
Available
Register Read more

AGI

  • This training course is for designers who require detailed knowledge of the DEIF controllers capabilities in order to make the right offer to meet application requirements.Designers will learn how to specify a genset controller with regards to option selection, how to design an application for DEIF controllers and how to setup advanced power management applications.

Your outcome

  • You will learn how to use the technical documentation as a tool for option selection to meet application requirements
  • Through practical exercises, you will learn to setup advanced power management applications using DEIF Utility Software
  • Via hands-on training you will gain knowledge about different modes of operation in power management applications
  • You will learn to emulate an entire application though practical application and function training

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

PPU 300

Operator/Service Read more
04-11-2020 - 05-11-2020
Skive, Denmark
EUR 850
Available
Register Read more

PPU 300

The two-day training course is for operators and service technicians. You will learn the basic functions of the PPU 300 controller and how to carry out daily routine operations. When familiar with the primary functions you will proceed with more advanced tasks such as setting up, troubleshooting and commissioning typical genset applications. 

Your outcome

  • You will learn the basic menu functions of the genset controller and become acquainted with the menu structure
  • You will learn how to use the controller and obtain in-depth knowledge of the functionality it offers.
  • You will learn how to use the different configuration inputs, modes of operation and how to change protection settings.
  • You will learn how to connect the utility software, configure I/O’s, parameter settings etc.

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

PPU 300

Codesys Read more
05-11-2020
Skive, Denmark
EUR 425
Available
Register Read more

PPU 300 Codesys

The PPU 300 CODESYS training is for switchboard builders and system integrators. The training course will provide you with tools and knowledge on how to use the PPU 300 in a CODESYS application. The training includes various hand-on sessions and will enable you to make customised project solutions.

Course prerequisites

Attending the PPU 300 Codesys training session tracompletion of the PPU 300 Service course. 

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

PPU 300

Operator/Service Read more
17-11-2020 - 18-11-2020
Skive, Denmark
EUR 850
Available
Register Read more

PPU 300

The two-day training course is for operators and service technicians. You will learn the basic functions of the PPU 300 controller and how to carry out daily routine operations. When familiar with the primary functions you will proceed with more advanced tasks such as setting up, troubleshooting and commissioning typical genset applications. 

Your outcome

  • You will learn the basic menu functions of the genset controller and become acquainted with the menu structure
  • You will learn how to use the controller and obtain in-depth knowledge of the functionality it offers.
  • You will learn how to use the different configuration inputs, modes of operation and how to change protection settings.
  • You will learn how to connect the utility software, configure I/O’s, parameter settings etc.

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

PPM 300

Operator/Service Read more
19-11-2020 - 19-11-2020
Skive, Denmark
EUR 850
Available
Register Read more

PPM 300

The two-day training course is for operators and service technicians. You will learn the basic functions of the PPM 300 controller and how to carry out daily routine operations. When familiar with the primary functions you will proceed with more advanced tasks such as setting up, troubleshooting and commissioning typical genset applications.

Your outcome

  • You will learn the basic menu functions of the genset controller and become acquainted with the menu structure
  • You will learn how to use the controller and obtain in-depth knowledge of the functionality it offers.
  • You will learn how to use the different configuration inputs, modes of operation and how to change protection settings.
  • You will learn how to connect the utility software, configure I/O’s, parameter settings etc.

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

AGC

Designer level Read more
26-11-2020 - 27-11-2020
Skive, Denmark
EUR 850
Available
Register Read more

AGC

  • This training course is for service technicians and engineers who commission and troubleshoot genset operations.

Your outcome

  • You will learn how to use the different configuration inputs, modes of operation, and how to change protection settings.
  • You will learn how to use the controller and obtain in-depth knowledge of the functionalities it offers.
  • You will learn how to access the menus from the front panel display screen to activate, commission and troubleshoot typical applications. Input from you on your typical applications further build these skills.
  • You will learn how to connect the utility software and configure I/Os, parameter settings, and additional operator panels (AOP). This will also involve tuning of PIDs, synchronisation and using the utility software as a troubleshooting tool.

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

AGC

Service level Read more
26-11-2020 - 27-11-2020
Skive, Denmark
EUR 850
Available
Register Read more

AGC

  • This training course is for service technicians and engineers who commission and troubleshoot genset operations.

Your outcome

  • You will learn how to use the different configuration inputs, modes of operation, and how to change protection settings.
  • You will learn how to use the controller and obtain in-depth knowledge of the functionalities it offers.
  • You will learn how to access the menus from the front panel display screen to activate, commission and troubleshoot typical applications. Input from you on your typical applications further build these skills.
  • You will learn how to connect the utility software and configure I/Os, parameter settings, and additional operator panels (AOP). This will also involve tuning of PIDs, synchronisation and using the utility software as a troubleshooting tool.

Training is a cornerstone to success

With the rapid advances in generator control and the increasingly sophisticated communication between engines themselves, it has become more necessary than ever for operators and service personnel to receive hands-on training.

DEIF commits to providing our customers with the information and resources necessary for the efficient use of our products. To that end, we offer training sessions for you and your associates to help you learn how to use DEIF generator controllers and software appropriately on our simulation equipment around the world. Attending a DEIF training session will enable you to provide your customers with cost-efficient solutions that meet all common requirements.  

We believe in learning by doing. Thus our courses involve hands-on training with simulation and emulation equipment in a clean, hazard-free, and controlled environment. Together we will simulate and troubleshoot a wide range of typical fault conditions and also applications based on input from the course participants without risking damage to your plant.

The sessions are carried out in small groups for greater flexibility and more involvement.

Register Close

Nyheder

Leder du efter software, dokumentation eller white papers?

Hos DEIF får du gratis og ubegrænset adgang til softwareopdateringer, teknisk dokumentation og ikke mindst inspirerende rapporter om nutidens og fremtidens brancherelevante emner.