TDU 107 Extended

1.3.3.0

10-09-2020

New features:

•    Further brandings are added.
•    AGC-4 as clock master is added.

Changes:

•    New entry point for the ECU measurement window is added.

Corrections:

•    Parameter max. value was not taken into account for text values.
•    If exactly 9 alarms were present, the last one was not visible.
•    Possibility to include system information when exporting a TDU.config file is added.
•    Preventive measures were taken to stabilize the VNC connection.
•    Generator measurements are removed from mains TDU.
•    Regeneration parameters are added to TDU.
•    Application supervision now supports mains with id´s 1-16 and DG´s with ID 17-32.

1.3.2.0

17-06-2020

New features:

• EIC measurements can now be seen in a separate window.
• Added support for new Boolean measurements.

Changes:

• More texts have been included in the translation file, to extend translation capabilities of the TDU. (Controller texts and Engine DM1/DM2 texts).
• Sync shortcut on the home screen now only requires a single press instead of a long press.
• Internal references to measurement layout on Modbus have been updated.
• Preferred font have been removed from the CSV file.

Corrections:

• Current status of the DG on the alternator curve now works properly.
• TDU Supervision is now updated correctly when using the Easy connect feature.
• Empty AOP texts are now saved during power cycle or in TDU.config files.
• "Autojump to sync scope" is now saved during power cycle or in TDU.config files.
• The screensaver now shows the "Connection lost" message.
• The branded splash screen is now shown correctly.

1.3.1.0

19-02-2020

New features:

•    Control panel instruments can now be custom scaled by pressing and holding for 3 seconds.
•    All voltage selections in parameter 9030 are now supported.
•    Access lock implemented; when the input is configured and active in the controller all settings are read only in the TDU.
•    New screen is added with current measurements shown graphically.
•    M-logic command "Inhibit. mode button" is now reflected in the TDU.
•    It is now possible to add a separate password for control panel instruments under "Permissions".
•    Fuel level is now shown in the top bar, if parameter 10980, 10990 or 11000 is set to "RMI fuel level" via the utility software.
•    Running hours is now shown in the top bar, if connected to a genset controller.
•    Parameter shortcut is added on the control page; it can be enabled/disabled under "Display settings".
•    Power Management ID and priority are added to the home screen, when connected to a genset controller.
•    Auto Jump to Synchroscope page is added; it can be enabled/disabled under "Display settings".
•    Import/ Export: It is now possible to load a configuration file from an older software version.

Changes:

•    20 pages are now available in the instrument panels on the control page.
•    Lists of instrument measurements have been expanded.
•    User access level filtering on the parameter page have been removed.
•    DM1/DM2 texts have been expanded.
•    When connected to a German AGC-4 with V0108 option, the manual button is removed.

Corrections:

•    Language management create export has been corrected, when specific German characters are used in the controller translation.
•    Visibility of the DM1 top icon has been corrected.

1.3.0.1

23-09-2019

Corrections:

• Corrected: AOP shortcut on control panel page.
• When changing mode, the confirmation dialogue now always pops up.

1.3.0.0

12-09-2019

New features:

• Support of AGC-4 mains controller.

• Import/export of following settings via USB:
          - Meters on homepage
          - Password levels
          - AOP texts
          - All settings under "Display config" 
• Added "Connection to controller" text on start-up screen.

Changes:

•    TDU backlight timeout introduced.
•    Fixed sporadic communication timeout messages on TDU.
•    Extended number of status texts on the TDU.

Corrections:

• Fixed screensaver freeze issue.
• Corrections to some status texts.
• Fixed rare initial communication issues.
• Create new master language function corrected

1.2.2.0

19-06-2019

Only supported on AGC-4 DG.
Minimum AGC-4 SW required: 4.72.0.

Changes:

• Internal production handling updated.

1.2.1.0

12-06-2019

New features:

• Implementation of offline USB update of TDU
• Added scrolling on supervision page
• Added hardcoded master password to DM1/DM2 clear button
• Enhanced user feedback during restart of TDU
• Added new EasyConnect text: "DG Ready to be added"

Changes:

• Improved connection stability between TDU and AGC-4 controller
• Change scaling of Fuel rate measurement

Corrections:

• Correct Modbus offset for escape mode timer
• Improved stability of auto connect feature
• Added missing password prompt to AOP shortcut on home screen
• Fixed misplaced buttons in control panel