Multi-line 2 AGC 150 Application Software

1.10.2

19-04-2022

PM compatibility: 1.25.0

Corrections:

• GOV output was sometimes raising to 100% when GB was closed with static sync. This has been fixed.
• Deutz EMR Stage V stop telegram corrected.

1.10.1

18-03-2022

PM compatibility: 1.25.0

Corrections:

• EIC autoviews is not deleted doing power up.
• EIC Deutz EMR Stage V: DEF level is shown and SPN5246 is mapped to m-logic eic derate active.
• MARINE EDG: GB stays closed in SEMI mode even though the STOP button is pressed.
• Translation issue seen when loading multiple languages is corrected.

1.10.0

28-02-2022

PM compatibility: 1.25.0

New features:

• Controller types 'Genset Marine' and 'Engine Drive Marine' added.
• DG HYBRID: Growatt CP100-CP250 & Growatt CP500-CP2250 PV protocols added.
• DG HYBRID: Growatt Mac, Max & Mid series PV protocol added.
• RMI Water temperature extended ranges.
• DG HYBRID: SMA Data Manager PV protocol added.
• Support of Perkins Stage V 120xJ (SU, VM) EIC protocol added.
• Support of Deutz EMR5 Stage V EIC protocol added.
• Activate/deactivate spinning reserve via M-Logic added.

Changes:

• DG HYBRID: Renamed "Growatt" PV protocol to "Growatt UE-series".

Corrections:

• DG HYBRID: Q share and DG cosphi limits now works correctly compared to the cosphi of the DG.
• Increased measurement inaccuracy at changing frequency could be seen infrequently.
• AMF Overlap is now working when modeshift is used with two or more MAINS units in power management.
• Numbers of view pages is updated correctly.

1.09.1

08-02-2022

PM compatibility: 1.24.2

Corrections:

• Logs stored correctly to work after a power cycle.

1.09.0

14-12-2021

PM compatibility: 1.24.2

New features:

• DG HYBRID: Added GoodWe HT Series PV protocol.
• DG HYBRID: Huawei V.3 PV protocol added. This protocol replaces all older Huawei protocols for newer inverter firmware versions.
• M-Logic input events for auto start command from any DG, any MAINS or any BATTERY in Plant.
• RPM based on calculation from the AC frequency reading.
• DG HYBRID: Added Havells 1-40kw PV protocol.
• DG HYBRID: Added Havells 50-70kw PV protocol.
• DG HYBRID: Added Sofar Solar 1-40kw PV protocol.
• DG HYBRID: Added Sofar Solar 50-70kw PV protocol.
• DG HYBRID: Added Chint (CPS) Boost 100-250kW PV protocol.
• M-Logic command for turning display backlight and all LEDs OFF added.

Changes:

• PM-id added to lower info line together with page-number and PM-prio.
• Multi-input wire-break setup: Delay, Auto acknowledge and Inhibit added.

Corrections:

• No ASC-4 PV irradiance sensor could make AGC DG's provide inadequate power for mains power export.
• Cosphi superior set points now work with only PV or Battery units on the busbar together with a AGC 150 mains.
• EIC and CIO communication can run at the same time again.

1.08.1

01-12-2021

PM compatibility: 1.24.2

Corrections:

• Minimum load was not respected when using droop curve 1.
• 'Guided view with genset' now shows start/stop buttons equal on all DG's in an ISLAND PMS setup.
• DG HYBRID: Added correct scaling for P/Q reference and changed the Broadcast ID to be 0xFF in the Polycab 50-60kW PV protocol.
• EIC generic J1939: Missing data readings (SPN 1119 and 1180) added to protocol.

1.08.0

11-11-2021

PM compatibility: 1.24.2

New features:

• PMS redundancy via Ethernet added.
• DG HYBRID: Added Modbus TCP/IP master communication support for PV and weather Modbus interfaces.
• DG HYBRID: New weather protocol for POA and BOM reading: Kipp & Zonen - RT1 Smart Rooftop Monitoring System.
• Added support of Cummins KTA19 EIC protocol.
• Added electrical load telegram to Caterpillar engine I/F.
• DG HYBRID: Havells 80-136kW PV protocol added.
• DG HYBRID: Polycab 50-60kW PV protocol added.
• DG HYBRID: FIMER PVS980 PV protocol added.
• Power ramp improved.
• Added support of Jichai EIC protocol.
• Added supported ECU types.
• Added Preheat functionality for Perkins Stage V.
• NTP Support added.

Changes:

• Maximum timer extended to 3200.0 s on a number of protections (AC, digital inputs, MPU, EIC).

Corrections:

• QSPI communication speed corrected.
• Self-check error 49 during read of log.
• DG HYBRID: EVVO PV active power control corrected.
• ISLAND deload of last GB now works as expected, so the GB opens when the frequency has dropped 0.5 Hz below nominal.
• Deload TB before GB opens function works correctly in PEAK SHAVING.
• FULL TEST available again. Was taken out in 1.04.2.
• DG HYBRID: POA and other weather-station values can now be written with DEIF OPEN communication.
• Analogue output limits for transducer output corrected, so min/max on input is reflected directly to output limits.
• PMS priority change via M-Logic or Modbus now works correctly.
• Fast OverCurrent max set point reduced from 350 % to 300 % due to alignment with data sheet. Backward compatibility compromised.
• If the ground relay was enabled and the application configuration was a non-PMS single DG, the GB would not open when deloaded.
• df/dt now operates on the mains side measurements.
• Configuration of outputs 15-18 is now correct after power cycle.
• Alarm texts are shown when the alarm is reviewed from CAT EMCP.

1.07.0

21-06-2021

PM compatibility: 1.24.1.

New features:

• Multiple busbars on CANshare is implemented, and 64 BTBs are available.
• Remote display functionality is added. This includes a new controller type.
• Reverse power: 3 AC protections are added.
• Support of Perkins Stage V EIC protocol is added.

Changes:

• MAINS connection are now allowed in the STAND ALONE variant and none GB or external GB.
• DG HYBRID: PV semi start/stop commands are added to M-Logic and to the Modbus commands.
• Weichai gas EIC protocol is updated with new data readings.

Corrections:

• "Fuel optimization" and "Fuel optimization + running hours" are now working with percent values.
• EIC transmission rate stability is improved.
• DG HYBRID: It is no longer possible for the unit to send negative P-ref set points to a PV inverter.
• Power emulation for AGC 150 with Option S1 is now calculated and shown correctly.
• DG HYBRID: Corrected an issue where Emulation PV was not able to start with PV protocol set to OFF.
• DG HYBRID: Corrected an issue where Goodwe DT and MT protocols would show negative ACP at values above 32768 W.

1.06.1

06-05-2021

Version 1.06.1 based on 1.06.0.

PM compatibility: 1.23.0.

Corrections:

• Limit events is added in M-Logic for Extended M-Logic Alarms.
• DVC 550/D550 now works with the EIC protocol Volvo Penta EMS 2.4.

1.06.0

29-04-2021

PM compatibility: 1.23.0.

New features:

• DG HYBRID: Added new parameter #17132 "Curtail threshold".
• Added support for John Deere Stage V EIC protocol.
• Added support for Isuzu EIC protocol.
• Added new parameter #6176 "Not running delay". Can be used as a hysteresis if the running feedback unexpectedly falls under the running detection level.
• Added support for Kohler EIC protocol.
• Added support for FPT + Iveco Stage V EIC protocol.
• Added four new M-Logic alarms with extended delay in menu 3620-3650.
• Added Event log entry when the application setup changes.
• DG HYBRID: Added monitoring tool for Modbus master communication within the service view under communication analysis.
• Added new GOV and AVR step test in parameter group #2970.
• DG HYBRID: Added support for Sungrow Logger 1000 PV protocol.
• DG HYBRID: Added support for Growatt PV protocol.
• Added keyswitch for Diesel engine.
• Added new controller type 'Engine Drive'.
  • Added MPU and EIC speed as PID1 input.
  • Added EIC as PID1 output.
  • Added digital input functions to control PID1 output (Semi manual mode).
  • Added ramp functionality for PID1.
  • Added new shortcut menu (Engine shortcuts).
• DG HYBRID: Added support of PV breaker.
• EIC speed (SPN 190) and MPU speed added to delta alarms.

Changes:

• Default views for DG are changed.
• Engine I/F list is reorganized in alphabetical order.
• Fuel pump logic is available for Stand-alone and Core software versions.
• The SunSpec identifying information shown in the display is improved.
• PV protocols are listed in alphabetic order in the display and the USW.
• DG HYBRID: Added fallback timer for power limit on SunSpec (Parameter 17180).
• Minimum timer for AC busbar alarms is decreased from 0.1 to 0.04 seconds.
• Text is changed in the shortcut menu.
• Engine emission system failure Tier4 icon now follows FMI levels and SPN3349 set to 7 for protocols with 10 ms transmission rate.

Corrections:

• Menu 6231 for GB close delay is no longer available when the application is power management.
• Corrected that strange texts sometimes were shown in the USW log.
• "L-L and P total" view now shows the correct value.
• Power factor set point on Modbus is now correctly initialized after power-up.
• General improvements to the D550/DVC 550 integration module.
• Ph-ph voltage will not saturate before the hardware limit is reached.
• Correct behavior of dfdt is now ensured when the number of periods are set above 12.
• The variable needed for angle check in Q dep U< alarm is updated.

1.05.4

06-04-2021

PM compatibility: 1.22.0.

Corrections:

• HYBRID: When reconfiguration of the RS-485 ports, power cycle of the unit is no longer needed.
• HYBRID: The unit is now able to automatically switch between Sunspec addresses (40000, 50000 and 0). If Sunspec initialization is not compatible, reinitialization starts in 20 seconds.

1.05.3

02-03-2021

PM compatibility: 1.22.0.

Corrections:

• Secured mode now works when Fuel optimisation is in use.
• Priority update now works when more than 16 gensets or more than 16 mains are present in a plant configuration.
• PMS priority data is properly maintained internally in all genset controllers.
• When digital input 50 is not used as feedback, it is no longer disturbing the check of breaker status.
• Breaker feedbacks are properly updated on the I/O status and the I/O setup page.

1.05.2

06-01-2021

PM compatibility: 1.22.0.

Corrections:

•  Support is added for Volvo engine with 60 Hz as primary speed when Volvo proprietary engine speed is used.
•  Generator under-frequency and under-voltage alarms are now inhibited during idle run.

1.05.1

08-12-2020

PM compatibility: 1.22.0.

Corrections:

•  AGC 150 Hybrid controller got stuck in Sunspec initialize, due to a previously unknown Modbus model in the ABB PVS175 PV inverter.
•  Transmitting DVC 550/D550 parameters over the CAN was irregular. This is corrected.

1-05-0

30-11-2020

PM compatibility: 1.22.0.

New features:

• Support for the new input configuration interface.
• DVC 550 PT100 measurements in display and selection in delta alarms.
• EIC start/stop as a parameter.
• M-Logic to start DG and close/inhibit close GB in auto mode. M-Logic to inhibit TB close.
• Scania EMS2 S8 Engine I/F.
• Configurable spinning reserve request using parameter 8930, not supported in BTB applications.
• Ground breaker to CORE package
• Shutdown override as new inhibit.
• Parameter to use nominal frequency or rpm as reference for EIC speed offset.
• Support for Volvo Penta EMS2.4.
• New combined views with electrical data.

Changes:

• Configurable multi inputs and new DM1 telegrams for JCB LiveLink. 
• Racked out breaker On/off displayed in log.
• Minimum level of "Frequency detection level (6165)" changed from 20hz to 10hz. 

Corrections:

• Ground relay routine improved:
        - There is now always an overlap when transferring ground relays between DGs.
        - The best DG to hold the ground relay now keeps it closed during de-load and transfer of the ground relay happens when the de-loading DG is ready to open its GB.
        - Older versions with ground relay enabled are no longer compatible going forward.
• AGC 150 Read log freezes controller. 
• Phase calculations are now properly performed and transmitted to the DVC 550 & D550 when changed through M-Logic.
• AC configuration in the D550/DVC 550 is now controlled by the AGC.
• When configured for split phase operation, the nominal voltage setpoint is now correctly calculated for the DVC 550/D550.
• New parameter #7746 DAVR AC config is introduced. This helps fix situations where the DAVR is not able to follow the AC configuration of the AGC.
• Configuring a mains standalone application with the CAN bus set to OFF in the application configuration prevented the MB from closing. This has been corrected.
• If a DG was running with its GB open and ground relay closed, and a mains then connected to the busbar, the ground relay would open. This has been corrected.
• Alternative engine speed control for Volvo protocols including counter and checksum is added. Can be enabled with the new parameter 15110.
• LTO now works correctly when unit is STAND-ALONE (non-sync).
• Multi input alarm level 2 Min/Max now updates correctly when output limits are changed from multi input configuration in USW.

1-04-2

22-09-2020

PM compatibility: 1.17.2.

Corrections:

•    TEST type in StandAlone (option S1) is limited to SIMPLE TEST.
•    Limit evaluation of multi-input 23 alarm for use in M-Logic is now working.
•    Included CAN Start/Stop in the Hatz proprietary CM1 telegram.
•    Current handling of TIER 4 icons for the Hatz protocol.
•    Read Aftertreatment 1 Intake Gas telegram for the Hatz protocol.
•    Necessary to force a regeneration until current feedback is received from ECU.
•    Fuel optimization + running hours does not swap DG's at fixed load.

1-04-1

29-07-2020

Version 1.04.1 based on 1.04.0

PM compatibility: 1.17.2

Corrections:

• Errors regarding powermanagement applications with PV, ASC and battery controller corrected.

1.03.1

14-05-2020

PM compatibility: 1.17.2.

Corrections:

• Analog output limits for the transducer output are corrected.
• Transducer input range is extended on multi inputs to support the setup of limits corrected in #1.
• STOP button has always a lid on the genset when running German rule, V0108.

1.03.0

03-04-2020

PM compatibility: 1.17.2

New features:

•    DVC 550 and D550 are now supported by the AGC.
•    Configurable amount of units for triggering Fatal CAN Error alarm, added in menu 8800.

Changes:

•    Emulated value for I>> alarms added.
•    Easy Connect is no longer blocking DG start in single DG applications.

Corrections:

•    In AMF situations where the mains had no TB, and #7065 mains fail ctrl was set to "Start engine" and the DGs had to connect through a BTB to supply the mains, the MB would not open as it did not have information about whether or not the DGs Hz/V OK timer had run out. And as the MB would not open the BTB would not close resulting in a deadlock. This has been corrected.
•    TB power capacity overrule timer will now run if there is an active MB trip failclass or the MB cannot be closed.
•    Ring bus applications: If BTBs were closed at and under application configuration, opening a BTB could cause a DG to start without a proper start signal.
•    Fixed a situation where opening a semi BTB, in a plant with an active start signal, would cause a DG to briefly engange its start prepare relay.

•    In a plant where all DGs are divided by open BTBs, if for example, DG1 is running and needs help from DG2, DG2 would start and close its breaker, then synchronize the BTB, and as the BTB would close, DG3 would briefly engange its start prepare relay. This has been fixed.
•    PMS + ISLAND + SEMI + GUIDED MIMIC: Start/stop buttons LED visible when relevant on genset.

1.02.0

26-03-2020

PM compatibility: 1.17.0.

New features:

•    Two new EIC aftertreatment alarms have been added: "High SOOT warning" and "High SOOT shutdown".

Changes:

•    Vector jump, df/dt, positive busbar sequence and directional over-current are now available in CORE MAINS and CORE BTB.
•    New TIER 4 icons for JCB EIC are added.

Corrections:

•    Parameter handling could in special cases cause decimals to be handled incorrectly in the display menu. This is corrected.
•    Problems with freeze and white screen are now prevented.
•    Analogue values from CIO 308 are now shown correctly in view-lines.
•    JUMP menu causing unwanted parameter change is corrected.
•    JUMP menu freeze is now prevented.
•    Overspeed 2 menu (4520) is now shown correctly.
•    GUIDED mimic is corrected with external breaker, so GB ON/OFF buttons do not lit up.

1.01.0

19-12-2019

PM compatibility: 1.17.0.

New features:

• EIC: JCB J1939 protocol is added.
• EIC: DEF level shown on lower tiny line in measure views. 
• Stand Alone (option S1) is implemented. Breaker selection is extended with 'No breaker' and 'External breaker'.
• LED colors can now be changed. An option to select a different LED color behavior in parameter 6084.
• Now it is possible to change the source address for PGN GC1 and CM1 independently of each other for all engine protocols.

Corrections:

• BTB can now be part of a plant with CORE units.

1.00.3

22-10-2019

PM compatibility: 1.17.0

Corrections:

• External BTB position feedbacks are now working again.
• Phase sequence error alarms are now working 3W3 coupling.
• Service timers can now be reset.
• Translated texts for I/O texts in Service View are now shown correctly.

1.00.2

05-08-2019

Version 1.00.2 based on 1.00.1

PM compatibility: 1.17.0

Corrections:

•    Deloading the TB is now properly handled in test mode when parameter #8273 "Deload TB back sync." is enabled
•    Multi inputs could go into overflow when set to voltage type
•    Internal analog outputs (52/55) now works correct when used with GP PID.
•    Genset priority would update even though the user had not issued an update.
•    If mains ATS is active, and TB is closed onto a healthy busbar, and the controller is powercycled, the TB no longer opens and closes on power up.
•    When sending a stop command during idle start the idle relay is kept closed.
•    Fixed situations where multi start would not work correctly in ISLAND and AMF applications.
•    M-Logic flag "Run all available island DG's" starts all DG's when activated.
•    Mimic for BTB and MAINS with External breaker updated, so the respective buttons (open/close) are not visible.
•    Various parameters added to parameter tree
•    Improved Easy Connect functionality:
        - Rapid menu changes prevented
        - Info text on removed units
        - Possibility to remove the other unit with pop-up when only 2 in plant
        - Better handling of fault situations (Appl. hazard or Duplicate CAN ID)
        - Removed units are no longer blocked from running
        - Faster indication of changes on the other units

1.00.0

30-04-2019

PM compatibility: 1.17.0

• Initial release