Off-grid hybrid power

Securing uptime with intelligent spinning reserve features, this automated solution guarantees minimum fuel consumption by maximising PV penetration without compromising minimum genset load requirements.

The DEIF power management automatically optimises the number of gensets connected to the busbar. In plants with different size gensets, the system even rotates the gensets automatically to ensure the most fuel-optimised genset match in accordance with the load request. Using CAN bus links between each power source, the reactive system boasts fast response times to changes in load demand or weather conditions.

The system is available as a Power Management or stand-alone solution for retrofits or existing plants.

Power management solution

ASC-4 applicable with AGC-4/AGC 200 controls up to 32 gensets
ASC PM appl. with AGC PM controls up to 32 gensets
Applications up to 16 sustainable power plants
Minimum genset load for optimal performance
Spinning reserve to ensure uptime
Maximise sustainable power penetration

Stand-alone solution

Applicable with all genset controls up to 16 gensets
Maximum 1 sustainable power plant
Minimum genset load for optimal performance
Maximise sustainable power penetration
MIC/MIB for detection of genset production

Can I help you?

Badrinarayanan Suresh

Vice President, Standard Business

+45 9614 9654 |

Advanced genset controller AGC 200

Up to 32 gensets in one plant
Synchronisation of up to 56 breakers in one plant
Multiple operating modes in one software
Multi-master power management
Load-dependent start and stop
Load management
Emulation for fast training and I/O test
Automatic Mains Failure sequence
Approved by TÜV and UL
Hot standby for full system redundancy
– change to backup genset controller on the fly
Close Before Excitation
– synchronisation from 6 seconds
Lifetime logging stored on SD card
Fully compatible with AGC-4 controllers
Suitable for hybrid power solutions fitted with ASC-4 controllers

Flere detaljer

Automatic sustainable controller ASC plant management

Maximising PV penetration
Spinning reserve demand
Minimum genset load requirement
Suitable for self-consumption and IPP applications
Support of SunSpec and other relevant protocols
Monitoring and supervision
Meteorological measurements
Fully integratable in AGC Power Management applications
Simple graphical configuration
Record time commissioning with DEIF Emulation – uses and verifies the functions of the real system for test, production and design
Suitable for power management solutions fitted with AGC PM genset controllers
Suitable for stand-alone solutions using multi-instruments such as DEIF’s MIB or MIC

Flere detaljer

Automatic sustainable controller ASC-4 Solar

Maximising PV penetration
Spinning reserve demand
Minimum genset load requirement
Suitable for self-consumption and IPP applications
Support of SunSpec and other relevant protocols
Monitoring and supervision
Meteorological measurements
Simple graphical configuration
Record time commissioning with DEIF Emulation – uses and verifies the functions of the real system for test, production and design
Suitable for power management solutions fitted with AGC-4 or AGC 200 genset controllers
Suitable for stand-alone solutions using multi-instruments such as DEIF’s MIB or MIC

Flere detaljer

Product solution

Integrable renewable hybrid power solution Integrable renewable hybrid power solution

Flere detaljer

Automatic genset controller AGC plant management

Fully scalable multi-master system of up to 992 gensets
Simple graphical configuration
Easy control from one central point of intelligence
Cost-optimised design
Reduced fuel consumption
Grid support
Monitoring and supervision
Emulation Solution – uses and verifies the functions of the real system for test, production and design
Suitable for hybrid power solutions fitted with ASC PM controllers

Flere detaljer

Automatic genset controller AGC-4

Up to 32 gensets in one plant

The intuitive, preprogrammed touch display saves you time and smoothes operation
Four general purpose PID regulators that control auxiliary systems
Synchronises up to 56 breakers in one plant
Multiple operating modes in one software
Multi-master power management
Load-dependent start and stop
Load management
Emulation for fast training and I/O test
Automatic Mains Failure sequence
Complies with: VDE AR-N 4110 (medium voltage, Germany), VDE AR-N 4105 (low voltage, Germany), EN 50549-1:2019 (Europe), ENA EREC G99 (United Kingdom). Option A10 required.
Approved by TÜV and UL
Tier 4 final support
Hot standby for full system redundancy
– change to backup genset controller on the fly
Redundant CANbus for power management
Close Before Excitation/Run-up synchronization
– synchronisation from 6 seconds
Fully compatible with AGC 150 and AGC 200 controllers
Suitable for hybrid power solutions fitted with ASC-4 controllers